Split-Spoke Deep-Lip Forged Wheel

A black intersecting split-spoke face sits inside a red outer barrel, with a deep lip and visible perimeter hardware. The contrast between the outer ring and intricate centre gives this design a distinctly layered appearance.

Finish note: the product images show a red barrel and black face, while the available option is labelled Silver. These are design examples, not confirmed Silver imagery. Confirm the finish and construction before ordering.

10 selectable combinations are recorded for this design: Silver, 4 / 5 holes and 18–22 in diameters. A hole count is not a complete bolt pattern. Width, PCD, offset and centre bore must be specified together for the intended vehicle.

The wider custom ranges below describe project possibilities, not additional ready-to-buy combinations. Different front and rear specifications should be listed separately in a custom enquiry.

Online diameters

18 in / 19 in / 20 in / 21 in / 22 in

Online hole counts

4 / 5

Selected colour label

Silver

Custom diameter range

15–26 in in the manufacturing information; other sizes require a separate specification and quote.

Listed PCD values

100, 108, 112, 115, 120, 127 and 130 mm; not a confirmation of a particular hole-count / PCD combination.

Listed offsets

ET 10 / 30 / 50 mm; the order-specific offset must be confirmed.

Centre bore

Custom specification; no fixed centre bore is assigned to the online options.

Width entry

The source width field reads 5.5 without a unit. Confirm the required width; do not treat this as a verified width for every diameter.

The manufacturing description gives the examples below for discussion. They are not ready-to-buy variants or vehicle compatibility statements. The final specification depends on vehicle data, brake clearance, suspension and the intended stance.

Example A

5 × 120 PCD / 72.6 mm centre bore / ET 20–45

Example B

5 × 112 PCD / 66.6 or 57.1 mm centre bore / ET 25–45

Example C

5 × 114.3 PCD / 60.1, 64.1 or 66.1 mm centre bore / ET 20–45

The manufacturing information identifies 6061-T6 aluminium alloy and a forged wheel construction. Product condition is listed as new, with origin in Anhui, China. No wheel net weight or numeric load rating is provided for these online combinations; request these for the final specification.

Two- and three-piece customization is described in the manufacturing information. The online size and drilling selectors do not specify which assembly is supplied. Confirm the piece count, hardware and finished appearance for the intended build.

For a custom enquiry, the manufacturing information illustrates polished, brushed, chrome, gradient coating and custom colour finishes. These are project possibilities, not additional online options or finishes included at the displayed price. The available colour label above remains the ordering option.

Material

6061-T6 aluminium alloy

Construction

Forged; final assembly to be confirmed

Condition

New

Origin

Anhui, China

For a custom quotation, provide the vehicle make and model, wheel diameter, width, bolt pattern (PCD), centre bore (CB) and offset (ET). Include the quantity and any different front / rear requirements. These measurements are more useful than a vehicle name alone.

Concavity, deep or stepped lips and centre-cap configuration can also be discussed for a custom project. The illustrated possibilities do not define the supplied construction or alter the standard online selection; request a confirmed drawing and specification for any design change.

The manufacturer describes customization of wheel dimensions, offsets, bolt patterns and centre bores, together with project development and specification confirmation. For unusual brakes or suspension changes, include the relevant clearance information before settling the final specification.

Drawing-based, sample-based and finish customization are listed project capabilities. Ask for the relevant scope, additional charges and approval steps; an online diameter selection does not itself include a bespoke design service.

The manufacturer describes CNC machining and checks covering dimensional accuracy, load rating, balance and surface finish. Its description also refers to quality control during production and a final AQL inspection before shipment. These are stated manufacturing procedures, not an independently verified test result for your selected combination.

Request the applicable inspection records and load information for the final wheel specification. The appearance of a wheel or a workshop image cannot establish its load capacity or suitability for a particular vehicle.

The manufacturing information lists a one-year warranty. Ask for the applicable coverage, exclusions and claim procedure in writing for your order; this reference does not replace the terms agreed with WheelVexa.

The manufacturer illustrates protective wrapping, foam supports around a wheel and individual carton packing. Confirm the protection, carton count and any custom packaging for the final order. The images are packaging examples, not a packing guarantee for every shipment.

The manufacturer describes sea freight, air freight and express options, plus cooperation with nominated forwarders. Trade quotations can address EXW, FOB or CIF arrangements. Route, freight cost, destination charges and order terms must be confirmed; these are not automatically included in the displayed wheel price.

Reference carton size

60 × 60 × 35 cm; source single-package data, subject to the final order.

Reference gross weight

18 kg per source package; not the net wheel weight or a rate for all variants.

The manufacturing FAQ gives indicative windows of up to 10 working days for stock orders, 20–30 days for production orders and 60–70 days for bespoke production. These timings begin after the agreed payment and order conditions are met. They are manufacturing references, not a promise of stock availability or arrival at your address.

The manufacturing FAQ mentions single-piece orders for inventory and paid samples when suitable stock is available. Sample cost and courier cost are paid by the buyer. Current sample availability, production minimums and final retail quantities must be confirmed for the selected specification.

This design is offered on a backorder basis, not as verified ready-to-ship inventory. Confirm fitment, finish, quantity, production timing and delivery arrangements before payment.

Logo and packaging customization are described for OEM and ODM projects. A trade enquiry should separate wheel specifications, required quantities, finish choices, branding artwork, packing requirements and destination. Custom branding or packaging is subject to a separate review and is not included simply by selecting a standard option.

For an individual build, choose the available size and hole count, then use the fitment enquiry when you need specification confirmation. For larger projects, use the dealer enquiry to request an order-specific proposal. The quote should identify the approved design, dimensions, finish, quantity, delivery terms and any sample or drawing approval.